Diferencia entre revisiones de «Especificaciones fabricación»

De Proyecto Butiá
Saltar a: navegación, buscar
(Placa USB4Butiá)
Línea 11: Línea 11:
 
|PIC 18F4550|| 1 || microcontroller||PIC18F4550     
 
|PIC 18F4550|| 1 || microcontroller||PIC18F4550     
 
|-
 
|-
|Socket 40pin||1||socket for the microcontroller||  
+
|Socket 40pin||1||socket for the microcontroller||under PIC18F4550
 
|-
 
|-
 
|RJ45 Female Jack||6|| 5555167-1 type ||RJ45
 
|RJ45 Female Jack||6|| 5555167-1 type ||RJ45
Línea 19: Línea 19:
 
|ax12 female bus connector||1|| molex WM18901-ND connector type||AX-12   
 
|ax12 female bus connector||1|| molex WM18901-ND connector type||AX-12   
 
|-
 
|-
|120R||1|| resistor||120Ω     
+
|120R||1||resistor 5% tolerance, 1/4w power||120Ω     
 
|-
 
|-
|390R||2|| resistor||390Ω
+
|390R||2|| resistor 5% tolerance, 1/4w power||390Ω
 
|-
 
|-
|1K||2|| resistor||1KΩ
+
|1K||2|| resistor 5% tolerance, 1/4w power||1KΩ
 
|-
 
|-
|10K||8|| resistor||10KΩ
+
|10K||8|| resistor 5% tolerance, 1/4w power||10KΩ
 
|-
 
|-
|1M||1|| resistor||1MΩ
+
|1M||1|| resistor 5% tolerance, 1/4w power||1MΩ
 
|-
 
|-
 
|22PF||2||capacitor||22pF
 
|22PF||2||capacitor||22pF

Revisión del 15:02 26 ene 2014

Placa USB4Butiá

Bill of Materials USB4Butiá
Component Quantity Description PCB Identifier
PIC 18F4550 1 microcontroller PIC18F4550
Socket 40pin 1 socket for the microcontroller under PIC18F4550
RJ45 Female Jack 6 5555167-1 type RJ45
USB Female Type B 1 USB_B
ax12 female bus connector 1 molex WM18901-ND connector type AX-12
120R 1 resistor 5% tolerance, 1/4w power 120Ω
390R 2 resistor 5% tolerance, 1/4w power 390Ω
1K 2 resistor 5% tolerance, 1/4w power 1KΩ
10K 8 resistor 5% tolerance, 1/4w power 10KΩ
1M 1 resistor 5% tolerance, 1/4w power 1MΩ
22PF 2 capacitor 22pF
0.1UF 4 capacitor 0.1uF
0.47UF 1 capacitor 0.47uF
electrolitic capacitor 10UF, 25V, 20% 1 lower than 7mm 10uF
Led 3mm 1 LED
20MHZ crystal 1 height 0.138" (3.50mm) Crystal 20MHZ
4.3mm switch 2 RST SW1, PROG SW2
Female Header 11 h1..h11


USB4Butiá Gerber file

Shield para motores

Bill of materials for USB4Butiá motor shield
Component Quantity Description PCB Identifier
L298HN 1 HBridge U1 L298
1A7 8 diode D1..D8
male headers 14 pin P1..P4
100nF (10V minimum, 20% tolerance) 2 ceramic capacitor C1, C2


USB4Butiá motor shield Gerber file

Placa Sensores

Bill of Materials allselasercut
Component Quantity Description PCB Identifier
Rj45 female jack 5 5555167-1 type RJ45
470uf electronic capacitor 1 25V C1 CAPAPOL
Resistor 10kΩ 4 5% tolerance, 1/4w power
Resistor 6.8kΩ 1 5% tolerance, 1/4w power
Resistor 120Ω 2 5% tolerance, 1/4w power
Resistor 1kΩ 2 5% tolerance, 1/4w power
Resistor 68kΩ 2 5% tolerance, 1/4w power
Led 2 high intensity green led like 365-1174-ND LED
Photoresistor 3 10K-200K OHM 4.20MM LXD4548 LDR
GP2Y0A21YK0F 1 Sharp Sensor 10-80cm sharp
Pushbutton 1 KS-03Q-02 SW_PUSH
Pushbutton cap 1 ACC-C17-6

each module specified in plantilla_allsenV2_lasercut-F_SilkS must be cuted with mouse bite technique or similar